more RC movies on my Channel:
http://www.youtube.com/user/bunterfisch/videos?flow=grid&view=0
Schöne Flugvorführung einer Bell 206 Jetranger mit Verbrenner Motor auf dem Flugplatz in Berlin Gatow zur Modellflieger Show 2014. Das Modell hatte ein Rotorkreisdurchmesser von 1,85m. Leider ist während des Fluges (wahrscheinlich) die Hecksteuerbrücke weg gerissen (im Video bei Minute 4:53 gut zu erkennen). Der Pilot hatte keine Chance. In dem vorangegangenen Video gab es auch Probleme mit einem Motorabsteller. Vielleicht ist durch die Autorotationslandung ein Teil der Heckanlenkung in Mitleidenschaft gezogen worden. Aber so ist das eben mit unserem Hobby. Ich selbst habe das schon einige male selbst miterlebt und kann dem Piloten nachfühlen. An der Stelle noch mal herzlichen Dank für die doch sehr schöne Flugdarbietung. Und…. nächstes Jahr in Gatow will ich ihn in neuen Glanz wieder fliegen sehn….
Recently Added Videos
){kind=link}
From what I can see, the tail rotor screw got loose, causing the blade to
tip and strike the Vertical stabilizer intern cutting of all circular
motion and causing the heli to go into a tail spin…
Great copter pilot – Must have been quite the bummer for him.
At 0:45 it looks like a real helicopter flying through the sky!
Sellotape will do the job, then it will be good as new
ohhh man echt schade um das Teil ;=) tut mir echt leid
Pretty good landing from what I see around here.
That damn thing hit a bug look at the tail section it slaps a bug in flight
I’ll stick to my indoor heli thank you very much
Sehr schöner Flug , aber leider kein gutes Ende ….
I think I just learned a German curse word. Lol
:-(
Bird strike
Das wäre kein Hobby für mich.Tausende investieren um Sie in den Sand zu
setzen in ein paar Minuten.
Dann doch lieber Standmodelle für die Vitrine im Wohnzimmer.
Sorry man! That looks $$$. Did you fix it? Anyways, your flying was very
good! Good job!
Tail rotor itself came loose, a screw wasn’t locktied or something, and the
tail rotor assembly, pitch-change plate and all, came loose and whacked the
vertical stabilizer fin. Might be able to autorotate, but he was too low
for that setup.
is it just me or a bird tried many times to take it down ?
“ECHT SUPER” Die Angst fliegt immer mit!
Que pena heim. Parece que foi atingido por um pássaro. Estava indo tão bem
Man that sucks , nice heli and good flying till the tail came off, I’ve had
my share of servos dying in mid air ,loose bolts , bad luck and bad flying
sometimes, just part of the hobby
20 Jul 2014
This pilot realy flys the helicopter and does some aggresive manouvers too.
Pitty he lost the heli in that way, but at least he was realy flying and
not just hovering an inch from the ground.
O.M.G.
If you pause at 4:54 you can see the tail rotor drive snap off. And then,
Scheisse! Even I know what that means. lol
Sorry for the loss.
Any survivors?
1 tiny lose rear rotor screw $0.02, Mamage because of that tiny screw
$2500.
Mr. Murphy made an appearance, there was miles of green grass versus a few
feet of concrete. Guess where it landed? GREAT heli, alot of work and
money, its obvious.
HS was too high also
What happened
Watch your video in slow motion, there are objects flying at high speed
during the flight of your helicopter.
looked like the main rotor flexed and chopped off the tail rotor.
D’Oh!
Sorry for your loss but that was the most scale-like flying of a model
helicopter that I have ever seen…
I like how the dude who filmed just said shit in German.
Voiletest Man
Pile of Crap
Die rote Leuchte ging immerhin noch.
The real “Angry Bird” is holding the remote control !!!
ok………….
базар жок
Game over ..500 euro parts
PLLLH
thats a boom strike
I think someone throw some stone
Hahahahahahaha
too much stress on the blade :P
Mains whacked off the stab and tail blades. I’m guessing either too little
clearance, squishy dampers in the head, or both.
I’m confused, what made the tail calasp like that? Was it moving to fast
when it was making the turn & just put a lot of stress on the tail? I went
to read the description & had no clue what it said.
Poor guy.
Ouch….